澳洲幸运5平台

水性路标漆乳液THYOSIL FT931


THYOSIL FT931

Acrylic polymer for high durability traffic markings

丙烯酸聚合物,用于高耐用性路标漆

Description描述

THYOSIL FT931 is an acrylic binder specially designed for manufacturing water based durable traffic paint.是专为配制水性耐用路标漆漆而设计的丙烯酸粘合剂。

Advantages优势

ü     Excellent durability. Requires less frequency of re application.良好的耐用性。

ü       Excellent retention of glass spheres.玻璃球的保留性好

ü      Quick dry.快干

Typical Properties典型值

These properties are typical values but do not constitute specifications.

 

Appearance外观

 

White emulsion白色乳液

 

 

 

 

Solids (%)固含量

46

 

 

 

 

pH

 

10

 

 

 

 

 

 

 

Viscosity at 25oC (cP)粘度

400

 

 

 

Density at25°C(g/ml)比重

1.06


Starting formulation using THYOSIL FT931基础配方


Raw material

(%)

THYOSIL FT931

52.90

POLACRIL D40 -Dispersant-分散剂

0.70

THYOSIL Q202 -Antifoam-消泡剂

0.30

Titanium dioxide钛白粉

3.00

Calcium carbonate碳酸钙

33.70

Methanol甲醇

4.50

Texanol 十二醇脂

2.90

THYOSIL Q202 -Antifoam-消泡剂

0.50

Water

1.50

Total

100.00








Manufacturing instructions加工介绍


1.       Load into the disperser with high agitation THYOSIL FT931, POLACRIL D40 and THYOSIL Q202.THYOSIL FT931, 分散剂 消泡剂加入 高搅拌分散机

2.       Slowly add the titanium dioxide and the calcium carbonate. Continue stirring for 15 minutes.

      慢慢加入钛白粉和碳酸钙,持续搅拌15分钟

3.       The paste obtained must be homogeneous. The particle size of the mill should be less than 5 microns.所得糊状物必须均匀,研磨的粒径应小于5微米。

4.       Prepare a mixture of methanol, Texanol, THYOSIL Q202 and water. Add this preparation slowly into the previous mixture.

      甲醇,十二醇脂消泡剂和水的预混,然后慢慢加入上述混合物。

5.       Incorporate 30% of retro-reflecting spheres of the desired particle size into this preparation.

         将30%所需粒度的反射球加入到上述混合物

Evaluation procedure评估程序


No Pick-Up Time (ASTM D711)路标漆不粘着时间的试验方法

Paint for vial demarcation was manufactured according to the formulation suggested above, incorporating microspheres of 150 microns. It was applied with roller, at21°Cand 55% of ambient humidity according to ASTM D711.

根据上述制剂制造用于小瓶分界的涂料,结合150微米的微球。 根据ASTM D711,在21℃和55%的环境湿度下用辊施加。

 

Properties属性

 

 

Results结果

 

Dry thickness干厚度

~19 mil 密尔

Drying time干燥时间

20 min 分钟

No Pick-Up Time (ASTM D711)不粘着时间

Pass通过






Recommendations for use使用建议


Paint with THYOSIL FT931 can be applied on asphalt with conventional or air-free sprays, concrete or previously painted lines that are well added to pavement.


A thin film (~580μm) will allow a faster drying, while a thicker film will allow for longer durability (~800 μm).


To achieve an optimal retro-reflectivity in thicker films, the use of larger glass particle microspheres is suggested.


The air and asphalt temperatures must be above10°Cduring the application. If relative humidity is greater than 90% the paints will require a longer drying time.


The cleaning of the equipment can be done with water or soapy solution.


Stainless Steel equipment and tools must be used, and typical solvents can be used to remove the dry paints from them.

用THYOSIL FT931做的的涂料可用于常规或无空气喷涂的沥青上,或以前绘制的线路,很好地添加到路面上。薄膜(〜580μm)将使干燥更快,而较厚的薄膜则可延长耐久性(约800μm)。为了在较厚的膜中实现最佳的反射率,建议使用较大的玻璃颗粒微球。在施工期间,空气和沥青的温度必须高于10°C。 如果相对湿度大于90%,涂料将需要更长的干燥时间。设备的清洁可以用水或肥皂液来完成。必须使用不锈钢设备和工具,并且可以使用典型的溶剂从其中除去干燥的涂料。




Safe handling and storage Information

Before using this product, read carefully the Material Safety Data Sheet (MSDS).








Note: The statements above are based on the current state of knowledge. They are intended to describe the product in relation to necessary safety precautions, and should not be used as a warranty of any specific property.


Revision: Februar y 2017


3

www.diransa.cn




© 版权所有·青岛澳洲幸运5官网有限公司   备案/许可证编号:鲁ICP备09036166号-2
地址:青岛市福州南路19号泛海名人广场4号楼603室      电话:86-0532-85788390      EMAIL:info@1msonline.com